- 视频数
- 614
- 订阅者
- 335万
- 总观看次数
- 3.4亿
- 最新上传
- 2026年11月14日
- 独立页面
- 木工
- 内容语言: 英语
- 地区: 美国
这是 Youtop 运营的独立目录页面，并非由 I Like To Make Stuff 或 YouTube 运营、赞助或认可。 提交更正. 你是这位创作者吗？认领此页面
Loading
这是 Youtop 运营的独立目录页面，并非由 I Like To Make Stuff 或 YouTube 运营、赞助或认可。 提交更正. 你是这位创作者吗？认领此页面
I Like To Make Stuff · 发布于 2015年10月27日
This reflection dampener is great for recording voice-over or any vocals. It's also easy and cheap to make! Sponsored by Johns Manville Share your winter prep projects at http://www2.jm.com/winterwarrior HERE'S WHAT YOU'LL NEED: 1/2" Plywood Sound control insulation Black material Aluminum angle Jigsaw - http://amzn.to/1PJEDxo Table Saw - http://amzn.to/1Mcwu53 Drill - http://amzn.to/1KrVA8p Stepped drill bits - http://amzn.to/1PJEMkz Staple Gun - http://amzn.to/1PJEERS I started with some scrap 1/2" plywood that was about 24" wide. I measured in 2" from each side and lightly nailed in a finishing nail. I bent a scrap of flexible veneer (you could use anything flexible) in between those two nails. I traced the outside of the arc with a pencil. You can move the piece in and out to change the overall arc shape. I measured 2" out from the line, and made some marks, following the line all of the way around. I went back and connected those marks. This gave me a second arc that was 2" away from my first line but had the same shape. I used a jigsaw (bleh.. don't like them) to cut out both lines. Jigsaws cause a lot of tear out on plywood, so I sanded all surfaces smooth. I used the arc as a template to create a duplicate, by tracing it onto the remaining plywood. I cut and sanded the second arc in the same way. Using 1/8" plywood scraps, I cut several strips 15" long and about 2" wide. Using brad nails, I connected the ends of one arc to the strips. I also added one strip on the back side of the in the center. I flipped the assemble upright and attached the second arc in the same way. I added the rest of the strips on the back side of the arcs every few inches. I made sure to add a strip along the outer edges of both sides. I cut a strip, about the same length as the inside of the arc, of insulation. I pushed the insulation into the shape of the arc, trying to evenly compress it. I cut some black material (about 1 yd.) down. Use fabric scissors if you have them! I laid the material over one edge and started stapling it in place. First, I moved down the inside of the arc, attaching the material with staples. Eventually, I wrapped it around, stretching it tight, both sides of the shape and stapled it down. I tried to get my final edges on the bottom side of the piece, then I cut off the excess with fabric scissors. I measured in 8" from the front edge, on both ends, and set a piece of angle aluminum in place. I marked the width on the angle bar. Using the mark as reference, I cut down the aluminum on the miter saw. On the piece, I marked the center point as well as 2" in from each side. I used a stepped bit to make the largest hole that I could, on the center mark. I made two smaller holes on each end, in that 2" space. These holes only need to be large enough for a screw to go through. I measured the 8" again on each side, placed the aluminum and screwed it into the plywood under the material. The unit was complete and just sat down around the threads on a microphone stand. Screwing on a microphone holder tightens down the aluminum, holding the whole assemble in place. Subscribe: http://bit.ly/ILikeToMakestuffSubscribe Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos Learn 3d modeling, get digital plans, and cool merch at https://iliketomakestuff.com Want to support ILTMS? Get exclusive content and more... http://www.iliketomakestuff.com/patreon FOLLOW: http://instagram.com/iliketomakestuff http://twitter.com/iliketomakestuff http://facebook.com/iltms #ILikeToMakeStuff About I Like To Make Stuff: We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more! These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about! Sound Reflection Dampener for audio recording // How-To | I Like To Make Stuff https://www.youtube.com/watch?v=yFnOjy-wde0 I Like To Make Stuff http://www.youtube.com/Iliketomakestuff
